Looking for a figure similar to this:
More or less the smae prportions with teh arms and legs, but needs to be about 4.5 or 5 inches tall. This guy would be perfect but is far too short.
Thanks
| JoeCustoms.com https://docs.joecustoms.com/forums/ |
|
| Need some figure advice, please? https://docs.joecustoms.com/forums/viewtopic.php?f=15&t=41548 |
Page 1 of 1 |
| Author: | Kambei [ Sat Aug 23, 2014 10:14 am ] |
| Post subject: | Need some figure advice, please? |
Looking for a figure similar to this: More or less the smae prportions with teh arms and legs, but needs to be about 4.5 or 5 inches tall. This guy would be perfect but is far too short. Thanks |
|
| Author: | DarkJedi [ Sat Aug 23, 2014 10:54 am ] |
| Post subject: | Re: Need some figure advice, please? |
Ummm, you could lengthen the legs (cut right above the boot) and add upper arms (cut at sleeve end). That would give you the height you need. |
|
| Author: | DarkJedi [ Sat Aug 23, 2014 10:54 am ] |
| Post subject: | Re: Need some figure advice, please? |
Ummm, you could lengthen the legs (cut right above the boot) and add upper arms (cut at sleeve end). That would give you the height you need. |
|
| Author: | Kambei [ Sat Aug 23, 2014 11:56 am ] |
| Post subject: | Re: Need some figure advice, please? |
The problem is that this figure has the exact proportions of arms/legs/torso I am looking for If it was twice the height it would be perfect |
|
| Author: | 2DARK2C [ Sat Aug 23, 2014 2:35 pm ] |
| Post subject: | Re: Need some figure advice, please? |
reminds me of the original series thundercat badguy/henchman ,toadish. |
|
| Author: | AdrienVeidt [ Sun Aug 24, 2014 8:43 am ] |
| Post subject: | Re: Need some figure advice, please? |
Wait about ten years for them to make him in the 6" Black line? |
|
| Author: | Kambei [ Sun Aug 24, 2014 2:29 pm ] |
| Post subject: | Re: Need some figure advice, please? |
Looks like it is going to be down to a full-on scratchbuild/sculpt. |
|
| Author: | roguetiger [ Sun Aug 24, 2014 4:12 pm ] |
| Post subject: | Re: Need some figure advice, please? |
http://www.industrialpolymers.com/produ ... ing-resin/ ? |
|
| Author: | Kambei [ Mon Aug 25, 2014 3:28 am ] |
| Post subject: | Re: Need some figure advice, please? |
roguetiger wrote: http://www.industrialpolymers.com/product-list/hydrospan-100-expanding-resin/ ? Almost impossible to get in the UK. Looked into Hydroshrink a while back. Did find one firm that had it, but they don't supply it to the public. The cost of getting it shipped over from America would be prohibitive, plus customs charges and other problems with customs. |
|
| Author: | Kambei [ Mon Aug 25, 2014 12:00 pm ] |
| Post subject: | Re: Need some figure advice, please? |
Going to try using this:  Will need a heckiva lot of filling and sanding, but the prportions are almost perfect. Will need to scratch-sculpt a head as well. |
|
| Author: | Lev [ Mon Aug 25, 2014 2:18 pm ] |
| Post subject: | Re: Need some figure advice, please? |
At least he's crazy poseable. |
|
| Author: | AdrienVeidt [ Mon Aug 25, 2014 7:17 pm ] |
| Post subject: | Re: Need some figure advice, please? |
Kambei wrote: Going to try using this: Will need a heckiva lot of filling and sanding, but the prportions are almost perfect. Will need to scratch-sculpt a head as well. Looks like he has noticulation below the neck, yo. Go for the RevolTech figure. |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|